Autowatch Ghost Immobiliser Installation
The Ghost is the UK's most advanced aftermarket immobiliser that works with CAN buses. It is discreet, does not use LED indicators or key fobs and is concealed in the vehicle's wiring.
It also permits the user to turn off the system temporarily through Transport Mode in the event of renting their vehicle. This guide will walk you through the process of installing the Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser protects your car from key cloning attacks, hacking attacks and relay attacks. The system is connected directly to the ECU of your car and protected by a PIN code you set. It is inaccessible to thieves using diagnostic scanners and other modern methods. It cannot be disabled by cutting circuits.
The system is simple to use, however professional installation is recommended to ensure a smooth connection with the ECU of your vehicle. A certified installer from Thatcham can assist in the installation and programming of your Ghost system. They can also suggest a tracking system or alarm to complement the protection package for your vehicle.
The first step is to disconnect your battery to prevent the possibility of airbag deployment and short circuits. Once this is done, the installer can safely begin work. Basic hand tools are helpful to make precise connections, while a multimeter can be used to check electrical values and safety. Cable tie and insulation tape are vital to secure connections and keep wiring neat. The Ghost Immobiliser user's guide will provide specific instructions tailored to your model.
It is essential to choose an area for grounding that is free of dirt or paint during installation. Installers should also ensure that the immobiliser's wires CAN H & CAN L are connected to the correct ECU ports. Depending on the model, these wires might need to be soldered or plugged into. To ensure a reliable and durable connection it is recommended that you choose a top-quality plug.
Once the install is complete After the installation is complete, the customer can turn on Transport Mode. This permits mechanics or valet parking to access the vehicle without knowing the pin code. The customer must press the service icon on the dashboard five times in two seconds. The system will confirm this by displaying 5 indicators.
The Autowatch Ghost 2 is a highly effective immobiliser that's TASSA certified and Thatcham approved. It's a great option for anyone who regularly rents their vehicle through platforms such as Turo. Immobilisers can also lower insurance costs since it significantly decreases the risk of theft.
Getting Started
If you are seeking a solution to protect your vehicle from thieves, you can't go wrong with an autowatch ghost immobiliser. It prevents your car from starting when someone copies or steals your key. It is possible because of its advanced technology that stops the engine from starting until the right PIN code is entered.
The device connects to the vehicle's bus network CAN and allows direct communication with the ECU. It makes use of buttons already on the dashboard and steering wheel to create a unique sequence that only you can identify and makes it impossible for others to start your vehicle. local ghost installer G28 Car Keys is the ultimate security system that protects your pride and joy and preserve its value should you decide to sell it in the future.
Installing Ghost's immobiliser is straightforward, but you must follow the steps to avoid electrical problems and malfunctions of the system. You'll need to locate a power supply of 12V and a solid grounding on the car's chassis. Then, you can begin connecting the wires to the immobiliser. Make sure to use high-quality connectors and soldering techniques to ensure a solid connection. Connect the connections with heat shrink tubing or insulation tape, or other materials to prevent short circuits of electricity.
Once the wires have been connected, you are able to connect the battery and start the engine to determine if the immobiliser is working. Once you have verified that everything is working properly and you are satisfied, you can place the immobiliser in a secure position inside the vehicle. Make sure to hide it properly to stop any thief from taking advantage of it.
The Ghost 2 immobiliser has been TASSA (Tracker and Aftermarket Security System Association), which means it is a top-quality deterrent to car thieves. It is resistant to hacking and key cloning and cannot be disabled without the code. The device is simple to use, and can be set into a service valet setting so that your vehicle will not be activated when you take it for an MOT or servicing.
Wiring
The Ghost Immobiliser is a cutting-edge security system designed to stop theft of vehicles. It is directly connected to the vehicle's CAN bus network and communicates with the ECU, making it a virtually undetectable addition to your car. In contrast to other aftermarket systems that require the removal of circuit components The Ghost Immobiliser does not interfere with any of the factory settings for your vehicle.
It's also totally undetectable by thieves using diagnostic scanning devices. This is because the system doesn't send and receive radio frequency signals, and it relies on the CAN data to communicate with your ECU. Furthermore, it doesn't require any modifications to your vehicle's existing key fobs.
Enter the sequence to disarm (either two or one buttons) and turn on the ignition of your vehicle to use Ghost Immobiliser. The indicator will flash twice to confirm that you have entered the correct code. You can now begin driving your car safely.
Once installed, Ghost Immobiliser guards your vehicle from key cloning or hacking while preserving its value. If you have to hand over your vehicle for service or valet parking, the Ghost Immobiliser can be temporarily disabled in Transport Mode.
You'll require a continuous power source (12V) as well as an earthing point to complete the installation of the Ghost immobiliser. Ensure that these are both well-insulated and safe to touch. Cable ties are also suggested for bundling and securing the wires. This reduces the possibility of theft by potential thieves. To avoid making mistakes, double-check these points and mark them using labels or tape. It's also a good idea to inspect every connection for signs of wear and tear. Make sure that all connections are in place, and properly protected. Don't forget to test your Ghost Immobiliser once the installation is completed. This will confirm that the unit is working properly and that all connections and insulation are secure. Make sure to address any issues as soon as they arise.
Testing
The Autowatch Ghost immobiliser is a revolutionary vehicle security system that works seamlessly with your car's ECU to prevent unauthorised motor starting. Its innovative technology protects your vehicle from key cloning, hacking, and other typical tactics thieves employ to steal vehicles. The Ghost is also able to work in conjunction with existing alarm and tracking systems to offer the ultimate vehicle protection. This system's unmatched features and secluded design make it a preferred option for car enthusiasts and security-conscious drivers too.
In order to ensure that the Ghost Immobiliser is properly integrated the Ghost Immobiliser, it is essential to follow the steps of the installation procedure. Consult the wiring diagram of your vehicle to assist you in locating and connecting the wires. Then, you'll need to identify the power source and grounding points. Once you've found them, you'll need to mark the points to make them easy to locate when installing. It's essential to use high-quality materials and tools. Basic hand tools can aid in making precise connections. A multimeter will verify electrical values, and ensure security. Insulation tape and cable ties can help keep connections neat and tidy. Additionally, a user's manual will provide specific instructions specifically tailored to your Ghost model.
Before beginning the installation, it's important to test the system by entering the PIN code and then starting the vehicle. This test will verify that the immobiliser is working according to plan, and prevents unauthorised vehicle start-ups. It is recommended to complete this step regularly as part of your regular inspections of the vehicle to ensure the system is always functioning correctly.
Once the installation has been completed, you are now able to start driving your car with confidence. The Ghost will keep your pride and joy safe from potential thieves and ensure that nobody is able to take off with your vehicle without the correct PIN code. The Ghost can be paired with an approved Thatcham tracker that detects any attempts to steal or tamper with. This will allow you to track your car in the event that it's stolen.
The Ghost is compatible with a wide variety of automobiles, including those from most major manufacturers. Monty's Locksmith can help you secure your vehicle with this cutting edge device. Contact us today to learn more about our service and installation options. We are a TASSA Installer who is registered This certification ensures that we adhere to strict standards and procedures for installing our products. This assures customers, insurance companies, and law enforcement agencies that installations are performed safely and in a safe manner.